DSpace-CRIS

Now showing 1 - 4 of 4

Some of the metrics are blocked by your
consent settings
Effect of a retrofitted metallic microfiber partial flow diesel particulate filter on a light duty diesel vehicle particle emission characteristics
(2024-02-01)
Mon Phyo, Mi Zwe
;
Phairote, Watanyoo
;
Srilomsak, Mek
;
Charoenphonphanich, Chinda
;
Masomtob, Manop
This study was conducted two distinct experiments, using a light-duty diesel vehicle at various engine speeds and loads as well as the new European driving cycle (NEDC) comparing commercial diesel fuel (B7) and pure biodiesel (B100). The NEDC involves a combination of urban and extra urban driving conditions. It aims to study a diesel vehicle's thermal efficiency as well as its gaseous and particulate matter (PM) emissions. This involves comparing results with and with no diesel oxidative catalyst (DOC) and a partial flow diesel particulate filter (PDPF) system. The surface morphology, micro- and nanostructure of a diesel vehicle's PM were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) to determine nanostructural and dimensional changes after mounting a DOC-PDPF system. Comparison of B7 and B100 combustion showed that B100 had around 1 % increase in brake thermal efficiency (BTE) at 1500 and 2000 rpm compared to B7 since B100 is a more oxygenated biofuel. At 2500 rpm, similar BTE values were observed. Introduction of a DOC-PDPF system resulted in an approximately 1 % BTE reduction for both fuels. This was due to greater friction losses caused by backpressure from the DOC-PDPF system. Increased exhaust backpressure was progressive, ranging from 1 kPa at idle speed to 6 kPa at high engine speeds for both tested fuels. The DOC-PDPF system respectively minimized PM emissions and particle numbers (PNs) by more than 50 % and 35 % for B7 and 71 % and 31 % for B100. These results are average values under the various phases of NEDC testing. A 30 % decrease in PM and a 44 % reduction in PNs under the overall test cycle were found when B100 was tested compared to B7. The soot primary particle size was reduced from 34.69 to 29.08 nm and the carbon fringe length diminished from 1.25 to 0.949 nm at different pre- and post-DOC-PDPF locations. This was due to partial oxidation on the surfaces of the PDPF metallic microstructure. PM undergoes simultaneous partial oxidation after passing through the DOC-PDPF system, as confirmed by TGA analysis.
Some of the metrics are blocked by your
consent settings
Physicochemical characteristics of ashes deposited on a wall flow diesel particulate filter of compression ignition engine
(2023-06-01)
Rodvanna, Sattatad
;
Srilomsak, Mek
;
Nuthong, Chaiwat
;
Charoenphanich, Chinda
;
Masomtob, Manop
The investigation of physicochemical characteristics of metal oxide ashes, deposited on a diesel particulate filter, was conducted using electron microscopy, energy dispersive spectroscopy, X-Ray fluorescence, and X-Ray diffractometry techniques. Iron is the main component of deposited ash on the DPF, and other ash components consisted of elements such as silicon, calcium, copper, sulfur, phosphorus, zinc, aluminum and minor chromium. It was clarified that this metal oxide ash has catalytic effect that contributed to an enhancement of soot oxidation. The apparent activation energies of soot oxidation on SiC powder and metal oxide ashes powder are approximately 169 and 135 kJ/mol, respectively.
Some of the metrics are blocked by your
consent settings
Influence of ethanol-biodiesel blends on diesel engines combustion behavior and particulate matter physicochemical characteristics
(2022-12-01)
Karin, Preechar
;
Tripatara, Aphichai
;
Wai, Phyo
;
Oh, Ban Seok
;
Charoenphonphanich, Chinda
Ethanol-blended biodiesel fuel can reduce smoke emissions by over 50% on both a single-cylinder engine and a four-cylinder engine. The average single primary particle size of biodiesel blended diesel, biodiesel, and ethanol blended biodiesel soot are approximately 30, 27, and 29 nm, respectively. The maximum graphene fringe length of biodiesel blended diesel, biodiesel, and ethanol blended biodiesel CI engine's soot are approximately 5.2, 4.6, and 4.5 nm. The carbon atom density of soot particles emitted from the diesel, biodiesel, and ethanol blended biodiesel CI engines are approximately 102, 91, and 88 atoms/nm3.
Some of the metrics are blocked by your
consent settings
Experimental investigation of the influence of ethanol and biodiesel on common rail direct injection diesel Engine's combustion and emission characteristics
(2022-11-01)
Wai, Phyo
;
Kanokkhanarat, Phobkrit
;
Oh, Ban Seok
;
Wongpattharaworakul, Veerayut
;
Depaiwa, Nattawoot
This study aims to characterize the effect of oxygenated biofuels in diesel engine combustion, thermal efficiency, and emission by blending different percentages of ethanol and biodiesel with fossil fuel derived diesel. In this research, 5% and 10% by weight of bioethanol were added to commercial B10 (10% biodiesel and 90% diesel), B20 (20% biodiesel and 80% diesel) and B100 (100% biodiesel) and experimented on using a 3 L four-cylinder common rail diesel engine. The experiment was performed under three engine speeds of 1000 rpm, 1500 rpm, and 2000 rpm with three constant engine torques of 56 Nm, 84 Nm, and 140 Nm. The results show that ethanol-biodiesel-diesel ternary blended fuels are higher in premixed combustion pressure and net heat release rate (NHRR) peaks. The cumulative heat release of ethanol blended fuels is also higher for ethanol blended fuels. The fuel consumption increased with the ethanol and biodiesel percentage in the blended fuels due to the lower heating value while the brake thermal efficiency did not decrease. It was clearly observed that the particle emission could be reduced by more than 50% when ethanol and biodiesel percentage increased.

KMITL

Browse

Filters

Settings

Sort By

Results per page

Search Results