KMITL

Permanent URI for this communityhttps://dspace.kmitl.ac.th/handle/123456789/1

Browse

Search Results

Now showing 1 - 5 of 5

Some of the metrics are blocked by your
consent settings
Impact of particulate filters on biodiesel and diesel fuel: a comparative study of thermal efficiency and emissions
(2026-06-01)
Suteerapongpun, Teerapat
;
Patkacha, Atikan
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Saisirirat, Peerawat
This study investigated the influence of a partial-flow (P-DPF) and a full-flow (F-DPF) diesel particulate filter on the combustion and emissions of a light-duty diesel engine fueled with conventional diesel (B7) and pure biodiesel (B100). The engine was operated on a dynamometer under engine speeds of 1600–2000 rpm at 84–140 Nm loads. The results revealed that while B100 had higher mass-based specific fuel consumption (BSFC) due to its lower energy density, its overall brake thermal efficiency (BTE) was comparable to that of B7, indicating similar energy conversion efficiency. The use of DPFs resulted in a modest efficiency penalty, with brake thermal efficiency decreasing by 0.07% for the P-DPF and 2.62% for the F-DPF. The emissions analysis revealed the trade-offs associated with biodiesel use and DPF integration. While baseline B100 operation produced substantially higher nitric oxide (NO) emissions relative to B7, it consistently generated much lower smoke opacity. When averaged across all three aftertreatment configurations (no DPF, P-DPF, and F-DPF), B100 reduced smoke emissions by approximately 59% compared with B7. Additionally, the P-DPF and F-DPF proved effective at reducing smoke to half and near-zero levels, respectively, for both fuels.
Some of the metrics are blocked by your
consent settings
Influence of ethanol-blended B7-diesel on in-cylinder combustion characteristic, engine thermal efficiency and emission of a 3L-compression ignition engine
(2026-03-01)
Suteerapongpun, Teerapat
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Saisirirat, Peerawat
;
Po-ngaen, Watcharin
This study investigated the effects of blending weight ratio of 5% and 10% ethanol (B7E5 and B7E10) with standard B7-diesel on the performance, combustion, and emission characteristics of a light-duty common-rail diesel engine. The engine was tested on a dynamometer across various speeds (1600–2000 rpm) and loads (84 and 112 Nm) to analyze in-cylinder pressure, thermal efficiencies, and exhaust emissions. Results indicated significant emission benefits, especially at high loads. The B7E10 blend reduced smoke intensity by approximately 75% and carbon dioxide emissions by 34% compared to the baseline B7. The performance analysis revealed a critical trade-off associated with the ethanol blends: while the inherent oxygen content in ethanol significantly improved the indicated thermal efficiency (ITE) through enhanced combustion, its lower viscosity simultaneously led to increased frictional losses. Consequently, these competing effects resulted in only a modest improvement in brake thermal efficiency (BTE) and comparable brake-specific energy consumption (BSEC) compared to the baseline B7. The primary objective is to identify the benefits and trade-offs associated with ethanol blending in biodiesel-based diesel fuels that are compatible with existing diesel vehicles.
Some of the metrics are blocked by your
consent settings
Particle emission and thermal efficiency analysis of a diesel vehicle using biodiesel and a platinum metallic partial-flow particulate filter
(2025-01-01)
Dang, Huy Quang
;
Phyo, Mi Zwe Mon
;
Thaeviriyakul, Poonnut
;
Cosh, Plan Teekatasn
;
Srilomsak, Mek
Harmful emissions from diesel vehicles, particularly unmodified ones, pose significant concerns for human health and the environment, underscoring the urgency to address these issues. This study investigated the effects of commercial fuels, B10, B20, and biodiesel B100, used with a metallic partial-flow catalyzed diesel particulate filter (P-CDPF), on a light-duty unmodified diesel vehicle's thermal efficiency and emissions characteristics. The initial test was conducted on a chassis dynamometer to measure the fuel flow rates at three different engine speeds, 1500, 2000, and 2500 rpm, with four loads, 84, 112, 140, and 160 Nm. This was done to evaluate brake-specific fuel consumption and brake thermal efficiency under steady-state conditions. The second test followed the new European driving cycle to examine emission factors of regulated pollutants under both urban and highway driving conditions. The results indicated that BSFC values increased with the biodiesel ratio in the blends, attributed to lower heating values. However, higher oxygen contents with increasing biodiesel ratios led to more complete combustion and improved brake thermal efficiency. Installation of a P-CDPF had a minimal impact, resulting in less than a 3.4% increase in the BSFC and a 1% decrease in brake thermal efficiency across all tested fuels, owing to its relatively low pressure drop. Increasing the biodiesel ratio from B10 and B20 to B100 resulted in reductions of up to 32% of particulate mass and 45% of particulate number in vehicle emissions. P-CDPF installation further reduced particulate mass by over 60% and particulate number by 36% across all tested fuels, demonstrating its effectiveness in trapping and passively oxidizing particulate matter. Furthermore, the P-CDPF significantly reduced harmful gases with addition of a catalytic coating. A combination of a P-CDPF and commercial biodiesel fuels emerges as an effective solution for reducing regulated emissions from unmodified diesel vehicles.
Some of the metrics are blocked by your
consent settings
The impact of a metallic partial-flow particulate filter on diesel engine combustion and emission characteristics using palm oil biodiesel blends
(2024-02-01)
Thin, Myat Hsu
;
Liu, Hai
;
Thaeviriyakul, Poonnut
;
Wai, Phyo
;
Oh, Ban Seok
Reducing particulate emissions from diesel engines pose a significant challenge in developing countries due to increasingly stringent regulations for both new and older vehicles. While employing wall-flow filters have proven effective for new vehicles, older vehicles necessitate alternative approaches to particulate filtration without complex modifications. Partial flow filters exhibit advantages in such scenarios, characterized by their lack of external components, simplified design, minimal maintenance demands, and resilience to misfuelling. The present study mainly focuses on the evaluation of a partial flow diesel particulate filter (P-DPF) installed on a diesel direct injection compression ignition engine, operating on commercial biodiesel blends, specifically B10 and B20. According to the combustion analyses, the combustion pressure, temperature, and the heat release rate increased with the kinetic energy inside the residual gas molecules due to installation of the P-DPF system. This also resulted in higher indicated power as well as indicated thermal efficiency. However, brake-specific fuel consumption and brake-specific energy consumption, exhibited only a marginal increase, while brake thermal efficiency experienced a slight decrease of 0.65% in the case of B10 and 0.74% for B20 after the installation of the P-DPF system due to the friction loss by the filter backpressure. Furthermore, an incremental increase in exhaust backpressure was observed, ranging from 0.2 kPa at 1000 rpm and 56 Nm to 2.25 kPa at 2000 rpm and 140 Nm. An analysis of emissions limits showed a notable 65% reduction in soot emissions. Comparative analyses were conducted to assess the impact of P-DPF installation on a diesel engine without any manual changes. Ultimately, the partial flow filter (P-DPF) emerges as an effective initial measure in mitigating particulate matter emissions, particularly when employed in a retrofit exhaust after-treatment system.
Some of the metrics are blocked by your
consent settings
Experimental investigation of the influence of ethanol and biodiesel on common rail direct injection diesel Engine's combustion and emission characteristics
(2022-11-01)
Wai, Phyo
;
Kanokkhanarat, Phobkrit
;
Oh, Ban Seok
;
Wongpattharaworakul, Veerayut
;
Depaiwa, Nattawoot
This study aims to characterize the effect of oxygenated biofuels in diesel engine combustion, thermal efficiency, and emission by blending different percentages of ethanol and biodiesel with fossil fuel derived diesel. In this research, 5% and 10% by weight of bioethanol were added to commercial B10 (10% biodiesel and 90% diesel), B20 (20% biodiesel and 80% diesel) and B100 (100% biodiesel) and experimented on using a 3 L four-cylinder common rail diesel engine. The experiment was performed under three engine speeds of 1000 rpm, 1500 rpm, and 2000 rpm with three constant engine torques of 56 Nm, 84 Nm, and 140 Nm. The results show that ethanol-biodiesel-diesel ternary blended fuels are higher in premixed combustion pressure and net heat release rate (NHRR) peaks. The cumulative heat release of ethanol blended fuels is also higher for ethanol blended fuels. The fuel consumption increased with the ethanol and biodiesel percentage in the blended fuels due to the lower heating value while the brake thermal efficiency did not decrease. It was clearly observed that the particle emission could be reduced by more than 50% when ethanol and biodiesel percentage increased.

KMITL

Browse

Filters

Settings

Sort By

Results per page

Search Results