KMITL

Permanent URI for this communityhttps://dspace.kmitl.ac.th/handle/kmitl/1

Browse

Settings

Author: search.filters.author.Phairote, W.

Search Results

Now showing 1 - 3 of 3
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    Experimental investigation of the impact ethanol-biodiesel-diesel blended fuels on combustion, emission, and performance of compression ignition diesel engine
    (2022-01-01)
    Wai, P.
    ;
    Karin, P.
    ;
    Phairote, W.
    ;
    Chollacoop, N.
    ;
    Kosaka, H.
    This research was directed to reduce the global diesel engine emissions and dependency on finite fossil fuel reserves. The ethanol was blended by weight ratio with commercial “B20” fuel (20% palm oil's biodiesel and 80% diesel) as B20E5 (95% B20 with 5% ethanol), B20E10 (90% B20 with 10% ethanol) and B20E20 (80% B20 with 20% ethanol). The results of the engine's performance, combustion, emission, and agglomerate particles size using blended fuels were compared with the results of based commercial B20 fuel. All fuel samples were tested on a four-cylinder direct injection diesel engine at a constant load of 140Nm with engine speeds of 1000RPM, 1500RPM and 2000RPM. When the engine speed increased, the brake-specific fuel consumption decreased, and the brake thermal efficiency increased. The B20E20 shows the highest brake-specific fuel consumption because of the low energy content of the fuel blend and the highest thermal efficiency because of a better combustion process. The ethanol-blended fuels show higher peaks of in-cylinder pressure and heat release rate than the base B20 fuel, with B20E20 as the highest. Ethanol blended fuels have significant advantages in particulate matters reduction, especially in idle engine speed. The blended fuels decreased soot and CO<inf>2</inf> emissions and increased NO<inf>x</inf> emission. The agglomerate particles size distribution was analysed with 100 samples for each fuel by using Scanning Electron Microscopy (SEM) and Image J tools. The average agglomerate particle size of B20, B20E5, B20E10 and B20E20 are 0.253 µm, 0.245 µm, 0.225 µm and 0.187 µm, respectively. As conclusion, adding ethanol to diesel fuel provide strong advantages on soot reduction and higher engine efficiency due to the enrich of fuel oxygen.
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    EFFECT OF BIODIESEL ON COMPRESSION IGNITION ENGINE’S COMBUSTION BEHAVIOR AND PARTICLE EMISSION
    (2020-11-11)
    Tripatara, A.
    ;
    Karin, P.
    ;
    Phairote, W.
    ;
    Charoenphonphanich, C.
    ;
    Masomtob, M.
    Diesel Engines are widely known for a high compression ratio, which is proportional to the engine’s efficiency. The effect from direct injection of a diesel engine generates particulate matter (PM). PMs are mainly composed of Soot and Metallic Ash, which are harmful to human health. This research describes thermal efficiency, engine performance and combustion behavior at various load (20%, 50%, and 80%) and fuel (B7, B20, and B100) by using combustion pressure analyzer. The experimental results demonstrated that B100 has the highest ISFC and lowest ISEC for all test series owing to the highest indicated thermal efficiencies. Operating load and fuel are strongly proportional to heat release rate and ignition delay. The heat release rate of low load condition is retarded compare with medium and high load. Conventional diesel and biodiesel PMs were investigated by using Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The average size of ultrafine particles that obtained from the experiment are range of 50-500 nm and primary nanoparticle size of B7 and B100 are in range of 25-50 nm.
      2
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    Influence of Metal Oxide Ashes on Soot Oxidation Kinetics and Nanostructure using Electron Microscopy and Thermogravimetric Analysis
    (2019-04-09)
    Koko, P.
    ;
    Karin, P.
    ;
    Saenkhumvong, E.
    ;
    Charoenphonphanich, C.
    ;
    Phairote, W.
    According to increasingly stringent regulations on particulate emission from automotive vehicles, diesel engine must be equipped with Diesel Particulate Filter (DPF) to trap the Particulate Matter (PM) which are very harmful to human health. Diesel particulate matters are composed primarily of unburned hydrocarbon (soot) and metal oxide ashes as solid fraction. DPF can trap PM with higher filtration efficiency and the process which can burn the soot into carbon dioxide is called regeneration process. Although regeneration process can burn the soot effectively, incombustible ashes will be remained inside the DPF channel causing engine back pressure. These metal oxide ashes are mainly derived from lubricant additives, engine wear and trace metals from diesel fuel. In this article, different nanostructures of diesel soot and metal oxide ash derived by diesel blending lube oil condition were briefly compared using Transmission Electron Microscopy (TEM) image analysis. Electron Dispersive X-ray Spectroscopy (EDS) analysis was introduced to investigate the chemical composition of particulate matters. Thermogravimetric Analysis (TGA) was also conducted to compare the oxidation kinetics of pure diesel soot and the influence of metal oxide ash on soot oxidation kinetics. Contamination of metal oxide ashes promoted soot oxidation rate due to the presence of metallic additives from lube oil acting as a catalyst on soot oxidation kinetics.
      3