KMITL

Permanent URI for this communityhttps://dspace.kmitl.ac.th/handle/123456789/1

Browse

Settings

Author: search.filters.author.Phairote, WatanyooSubject: search.filters.subject.Particulate matter

Search Results

Now showing 1 - 2 of 2
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    Effect of a retrofitted metallic microfiber partial flow diesel particulate filter on a light duty diesel vehicle particle emission characteristics
    (2024-02-01)
    Mon Phyo, Mi Zwe
    ;
    Phairote, Watanyoo
    ;
    Srilomsak, Mek
    ;
    Charoenphonphanich, Chinda
    ;
    Masomtob, Manop
    This study was conducted two distinct experiments, using a light-duty diesel vehicle at various engine speeds and loads as well as the new European driving cycle (NEDC) comparing commercial diesel fuel (B7) and pure biodiesel (B100). The NEDC involves a combination of urban and extra urban driving conditions. It aims to study a diesel vehicle's thermal efficiency as well as its gaseous and particulate matter (PM) emissions. This involves comparing results with and with no diesel oxidative catalyst (DOC) and a partial flow diesel particulate filter (PDPF) system. The surface morphology, micro- and nanostructure of a diesel vehicle's PM were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) to determine nanostructural and dimensional changes after mounting a DOC-PDPF system. Comparison of B7 and B100 combustion showed that B100 had around 1 % increase in brake thermal efficiency (BTE) at 1500 and 2000 rpm compared to B7 since B100 is a more oxygenated biofuel. At 2500 rpm, similar BTE values were observed. Introduction of a DOC-PDPF system resulted in an approximately 1 % BTE reduction for both fuels. This was due to greater friction losses caused by backpressure from the DOC-PDPF system. Increased exhaust backpressure was progressive, ranging from 1 kPa at idle speed to 6 kPa at high engine speeds for both tested fuels. The DOC-PDPF system respectively minimized PM emissions and particle numbers (PNs) by more than 50 % and 35 % for B7 and 71 % and 31 % for B100. These results are average values under the various phases of NEDC testing. A 30 % decrease in PM and a 44 % reduction in PNs under the overall test cycle were found when B100 was tested compared to B7. The soot primary particle size was reduced from 34.69 to 29.08 nm and the carbon fringe length diminished from 1.25 to 0.949 nm at different pre- and post-DOC-PDPF locations. This was due to partial oxidation on the surfaces of the PDPF metallic microstructure. PM undergoes simultaneous partial oxidation after passing through the DOC-PDPF system, as confirmed by TGA analysis.
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    Experimental investigation of metallic partial-flow particulate filter on a diesel engine's combustion pressure and particle emission
    (2023-09-01)
    Mon Phyo, Mi Zwe
    ;
    Wai, Phyo
    ;
    Thin, Myat Hsu
    ;
    Oh, Ban Seok
    ;
    Phairote, Watanyoo
    The study aims to present the combustion and exhaust behaviors of a 3 L, four-cylinder common rail diesel engine with three different kinds of conventional B7 diesel fuels with and without a platinum diesel oxidation catalyst (DOC) system and non-catalytic partial flow through a diesel particulate filter (P-DPF). Testing is performed under the three different operating conditions, idle to medium engine loading at 1000, 1500, and 2000 engine revolutions per minute with four different engine torques of 84, 112, 140 and 160 Nm. The surface morphology and agglomerate size of particulate matter (PM), single primary particle analysis as well as the fringe length of the carbon crystallite structure were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive x-ray spectroscopy (EDS) to achieve a better understanding through image processing. The P-DPF system does not have a significant effect on an engine's in-cylinder combustion characteristics and brake thermal efficiency. The diesel engine's particle emissions are reduced by trapping them on the metallic micro-fibers of a P-DPF. CO<inf>2</inf>, NO, and O<inf>2</inf> levels show that the carbonaceous particle emissions on the micro-structure of the P-DPF passively react with NO<inf>2</inf> and O<inf>2</inf>. Consequently, diesel engine particle emissions can be reduced by around 50% using a P-DPF system under the experimental conditions of the current study.