KMITL

Permanent URI for this communityhttps://dspace.kmitl.ac.th/handle/123456789/1

Browse

Search Results

Now showing 1 - 5 of 5

Some of the metrics are blocked by your
consent settings
Impact of particulate filters on biodiesel and diesel fuel: a comparative study of thermal efficiency and emissions
(2026-06-01)
Suteerapongpun, Teerapat
;
Patkacha, Atikan
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Saisirirat, Peerawat
This study investigated the influence of a partial-flow (P-DPF) and a full-flow (F-DPF) diesel particulate filter on the combustion and emissions of a light-duty diesel engine fueled with conventional diesel (B7) and pure biodiesel (B100). The engine was operated on a dynamometer under engine speeds of 1600–2000 rpm at 84–140 Nm loads. The results revealed that while B100 had higher mass-based specific fuel consumption (BSFC) due to its lower energy density, its overall brake thermal efficiency (BTE) was comparable to that of B7, indicating similar energy conversion efficiency. The use of DPFs resulted in a modest efficiency penalty, with brake thermal efficiency decreasing by 0.07% for the P-DPF and 2.62% for the F-DPF. The emissions analysis revealed the trade-offs associated with biodiesel use and DPF integration. While baseline B100 operation produced substantially higher nitric oxide (NO) emissions relative to B7, it consistently generated much lower smoke opacity. When averaged across all three aftertreatment configurations (no DPF, P-DPF, and F-DPF), B100 reduced smoke emissions by approximately 59% compared with B7. Additionally, the P-DPF and F-DPF proved effective at reducing smoke to half and near-zero levels, respectively, for both fuels.
Some of the metrics are blocked by your
consent settings
Influence of ethanol-blended B7-diesel on in-cylinder combustion characteristic, engine thermal efficiency and emission of a 3L-compression ignition engine
(2026-03-01)
Suteerapongpun, Teerapat
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Saisirirat, Peerawat
;
Po-ngaen, Watcharin
This study investigated the effects of blending weight ratio of 5% and 10% ethanol (B7E5 and B7E10) with standard B7-diesel on the performance, combustion, and emission characteristics of a light-duty common-rail diesel engine. The engine was tested on a dynamometer across various speeds (1600–2000 rpm) and loads (84 and 112 Nm) to analyze in-cylinder pressure, thermal efficiencies, and exhaust emissions. Results indicated significant emission benefits, especially at high loads. The B7E10 blend reduced smoke intensity by approximately 75% and carbon dioxide emissions by 34% compared to the baseline B7. The performance analysis revealed a critical trade-off associated with the ethanol blends: while the inherent oxygen content in ethanol significantly improved the indicated thermal efficiency (ITE) through enhanced combustion, its lower viscosity simultaneously led to increased frictional losses. Consequently, these competing effects resulted in only a modest improvement in brake thermal efficiency (BTE) and comparable brake-specific energy consumption (BSEC) compared to the baseline B7. The primary objective is to identify the benefits and trade-offs associated with ethanol blending in biodiesel-based diesel fuels that are compatible with existing diesel vehicles.
Some of the metrics are blocked by your
consent settings
Effect of a retrofitted metallic microfiber partial flow diesel particulate filter on a light duty diesel vehicle particle emission characteristics
(2024-02-01)
Mon Phyo, Mi Zwe
;
Phairote, Watanyoo
;
Srilomsak, Mek
;
Charoenphonphanich, Chinda
;
Masomtob, Manop
This study was conducted two distinct experiments, using a light-duty diesel vehicle at various engine speeds and loads as well as the new European driving cycle (NEDC) comparing commercial diesel fuel (B7) and pure biodiesel (B100). The NEDC involves a combination of urban and extra urban driving conditions. It aims to study a diesel vehicle's thermal efficiency as well as its gaseous and particulate matter (PM) emissions. This involves comparing results with and with no diesel oxidative catalyst (DOC) and a partial flow diesel particulate filter (PDPF) system. The surface morphology, micro- and nanostructure of a diesel vehicle's PM were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) to determine nanostructural and dimensional changes after mounting a DOC-PDPF system. Comparison of B7 and B100 combustion showed that B100 had around 1 % increase in brake thermal efficiency (BTE) at 1500 and 2000 rpm compared to B7 since B100 is a more oxygenated biofuel. At 2500 rpm, similar BTE values were observed. Introduction of a DOC-PDPF system resulted in an approximately 1 % BTE reduction for both fuels. This was due to greater friction losses caused by backpressure from the DOC-PDPF system. Increased exhaust backpressure was progressive, ranging from 1 kPa at idle speed to 6 kPa at high engine speeds for both tested fuels. The DOC-PDPF system respectively minimized PM emissions and particle numbers (PNs) by more than 50 % and 35 % for B7 and 71 % and 31 % for B100. These results are average values under the various phases of NEDC testing. A 30 % decrease in PM and a 44 % reduction in PNs under the overall test cycle were found when B100 was tested compared to B7. The soot primary particle size was reduced from 34.69 to 29.08 nm and the carbon fringe length diminished from 1.25 to 0.949 nm at different pre- and post-DOC-PDPF locations. This was due to partial oxidation on the surfaces of the PDPF metallic microstructure. PM undergoes simultaneous partial oxidation after passing through the DOC-PDPF system, as confirmed by TGA analysis.
Some of the metrics are blocked by your
consent settings
Experimental investigation of metallic partial-flow particulate filter on a diesel engine's combustion pressure and particle emission
(2023-09-01)
Mon Phyo, Mi Zwe
;
Wai, Phyo
;
Thin, Myat Hsu
;
Oh, Ban Seok
;
Phairote, Watanyoo
The study aims to present the combustion and exhaust behaviors of a 3 L, four-cylinder common rail diesel engine with three different kinds of conventional B7 diesel fuels with and without a platinum diesel oxidation catalyst (DOC) system and non-catalytic partial flow through a diesel particulate filter (P-DPF). Testing is performed under the three different operating conditions, idle to medium engine loading at 1000, 1500, and 2000 engine revolutions per minute with four different engine torques of 84, 112, 140 and 160 Nm. The surface morphology and agglomerate size of particulate matter (PM), single primary particle analysis as well as the fringe length of the carbon crystallite structure were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive x-ray spectroscopy (EDS) to achieve a better understanding through image processing. The P-DPF system does not have a significant effect on an engine's in-cylinder combustion characteristics and brake thermal efficiency. The diesel engine's particle emissions are reduced by trapping them on the metallic micro-fibers of a P-DPF. CO<inf>2</inf>, NO, and O<inf>2</inf> levels show that the carbonaceous particle emissions on the micro-structure of the P-DPF passively react with NO<inf>2</inf> and O<inf>2</inf>. Consequently, diesel engine particle emissions can be reduced by around 50% using a P-DPF system under the experimental conditions of the current study.
Some of the metrics are blocked by your
consent settings
Effect of Metallic Microfiber Flow Through Diesel Particulate Filter System on Diesel Engine’s Particle Emission Physicochemical Characteristics
(2023-03-01)
Oh, Ban seok
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Srilomsak, Mek
;
Charoenphonphanich, Chinda
It is well known that particulate matter (PM) from diesel compression ignition engines is harmful to the environment and to human health. To reduce engine PM emissions, exhaust after-treatment systems are utilized. A basic high-performance system can be composed of a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF). This study used a system composed of a DOC and a partial flow DPF. Partial flow refers to how only a portion of the exhaust gas is filtered using metal fibrous filters instead of the full flow using ceramic filters. The PM deposited on the side wall of the stages of the system was investigated with respect to elemental composition, morphology, and nanostructure. This was to determine the effect of each component on the PM. The elemental composition analysis found traces of the engine lubricant oil in the PM collected before entering the DOC. This was then eliminated by the DOC and the remaining PM was not significantly impacted by the exhaust after-treatment system. The morphology and nanostructure show an interesting relationship where the size of the single primary particles increased while the graphitic nature of the carbon in the PM seemed to decrease. This can be explained by the simultaneous nature of partial trapping and partial oxidation that occurs in the partial-flow DPF. The emission measurements of opacity, temperature, CO<inf>2</inf>, NO, and O<inf>2</inf> from each position also support this.

KMITL

Browse

Filters

Settings

Sort By

Results per page

Search Results