KMITL

Permanent URI for this communityhttps://dspace.kmitl.ac.th/handle/123456789/1

Browse

Settings

Author: search.filters.author.Nanan, K.Subject: search.filters.subject.Swirl flow

Search Results

Now showing 1 - 3 of 3
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Item,
    Heat transfer enhancement by tapered twisted tape inserts
    (2015-10-01)
    Piriyarungrod, N.
    ;
    Eiamsa-ard, S.
    ;
    Thianpong, C.
    ;
    Pimsarn, M.
    ;
    Nanan, K.
    The effects of inserted tapered twisted tapes, their taper angle and twist ratio on heat transfer rate, pressure drop and thermal performance factor characteristics have been reported. The experiments were carried out by using the tapered twisted tapes with 4 different taper angles which θ= 0.0° (typical twisted tape), 0.3°, 0.6° and 0.9°. At each taper angle, the tapered twisted tapes were twisted at three different twist ratios (y/W) of 3.5, 4.0 and 4.5. All tapes were tested under turbulent flow regime for Reynolds numbers between 6000 and 20,000. A twist ratio is defined as the ratio of twist length (y) to twisted tape width at the large end (W). The plain tube was also tested for comparison. Heat transfer enhancement and friction loss increased with decreasing taper angle and twist ratio. Thermal performance factor tended to increase with increasing taper angle and decreasing tape twist ratio. For the present range, the tube with the tape with taper angle (θ) of 0.9° and twist ratio (y/W) of 3.5 yielded the maximum thermal performance factor of 1.05 at Reynolds number (Re) of 6000.
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Item,
    Thermohydraulic characteristics of co/counter swirl flow through a round tube fitted with helical screw tape and twisted tape
    (2013-03-01)
    Eiamsa-Ard, S.
    ;
    Yongsiri, K.
    ;
    Nanan, K.
    ;
    Thianpong, C.
    Influence of co/counter swirl flow on the characteristics of friction, heat transfer and thermal performance factor in heat exchanger tubes has been experimentally investigated. Each twisted tape is inserted into a helical screw tape and then these combined tapes are subsequently equipped in a heat exchanger tube for generating the swirl flow. The combined tapes are arranged in two different forms, namely (i) co-swirl arrangement in which their twist are in the same direction and (ii) counter-swirl arrangement in which their twists directions are in the opposite directions. The experiments using helical tapes alone are also performed for assessment. The helical screw tapes are used at three different tape-twist ratios (PR = p/D = 1.0, 1.5 and 2.0), each with three different tape-width ratios (WR = w/D = 0.15, 0.2 and 0.25), while twisted tapes are used at three different twist ratios (YR = y/W = 3, 4 and 5). The results show the maximum thermal performance factor of 1.49 for helical tape alone with PR=2.0 and WR=0.2. At similar conditions, the heat transfer rate associated with the combined tapes in counter-swirl arrangement is 3.4% and 10% higher than those in co-swirl arrangement and helical tape alone.
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Item,
    Heat transfer enhancement in a rectangular channel with twisted tape inserts
    (2009-01-01)
    Nuthong, W.
    ;
    Eiamsa-Ard, S.
    ;
    Nanan, K.
    ;
    Eiamsa-Ard, P.
    ;
    Thianpong, C.
    Experimental investigation of heat transfer and friction factor behaviors in a rectangular channel with multiple twisted tapes (MTTs) is carried out. In each run, five MTTs are simultaneously used as the swirl flow generators in a test section. The lower wall of the channel is subjected to uniform heat flux conditions while the upper wall is insulated. Parametric runs are made for Reynolds numbers ranging from 2700 to 9000, the tapes with twist-length to twist-width ratios (y/w) of 3, 4 and 5 while the aspect ratio of AR = W/H = 10 is fixed throughout. Experiments using smooth channel are also performed for comparison. The experimental results reveal that heat transfer in the channels with MTTs at twist ratios (y/w) of 3, 4 and 5 are respectively increased around 55%, 37% and 22% over those in the smooth channel. In addition, the empirical correlations of the Nusselt number and friction factor in the developed flow region for the channels fitted with MTTs are also derived.