Srilomsak, Mek

Loading...
Thumbnail Image
Preferred name
Srilomsak, Mek
Alternative Name
Srilomsak, M.
Main Affiliation
Email
mek.sr@kmitl.ac.th

Settings

Now showing 1 - 2 of 2
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    Particle emission and thermal efficiency analysis of a diesel vehicle using biodiesel and a platinum metallic partial-flow particulate filter
    (2025-01-01)
    Dang, Huy Quang
    ;
    Phyo, Mi Zwe Mon
    ;
    Thaeviriyakul, Poonnut
    ;
    Cosh, Plan Teekatasn
    ;
    Srilomsak, Mek
    Harmful emissions from diesel vehicles, particularly unmodified ones, pose significant concerns for human health and the environment, underscoring the urgency to address these issues. This study investigated the effects of commercial fuels, B10, B20, and biodiesel B100, used with a metallic partial-flow catalyzed diesel particulate filter (P-CDPF), on a light-duty unmodified diesel vehicle's thermal efficiency and emissions characteristics. The initial test was conducted on a chassis dynamometer to measure the fuel flow rates at three different engine speeds, 1500, 2000, and 2500 rpm, with four loads, 84, 112, 140, and 160 Nm. This was done to evaluate brake-specific fuel consumption and brake thermal efficiency under steady-state conditions. The second test followed the new European driving cycle to examine emission factors of regulated pollutants under both urban and highway driving conditions. The results indicated that BSFC values increased with the biodiesel ratio in the blends, attributed to lower heating values. However, higher oxygen contents with increasing biodiesel ratios led to more complete combustion and improved brake thermal efficiency. Installation of a P-CDPF had a minimal impact, resulting in less than a 3.4% increase in the BSFC and a 1% decrease in brake thermal efficiency across all tested fuels, owing to its relatively low pressure drop. Increasing the biodiesel ratio from B10 and B20 to B100 resulted in reductions of up to 32% of particulate mass and 45% of particulate number in vehicle emissions. P-CDPF installation further reduced particulate mass by over 60% and particulate number by 36% across all tested fuels, demonstrating its effectiveness in trapping and passively oxidizing particulate matter. Furthermore, the P-CDPF significantly reduced harmful gases with addition of a catalytic coating. A combination of a P-CDPF and commercial biodiesel fuels emerges as an effective solution for reducing regulated emissions from unmodified diesel vehicles.
      1
  • Loading...
    Thumbnail Image
    Some of the metrics are blocked by your 
    consent settings
    Item type:Publication,
    Characterization of biodiesels and tire derived particulate matters in morphology and nanostructure
    (2022-01-01)
    Oh, Ban seok
    ;
    Karin, Preechar
    ;
    Srilomsak, Mek
    ;
    Chonvasin, Kritin
    ;
    Po-ngen, Watcharin
    Particulate Matters (PM) are known to be dangerous to human health and the environment. Regulations have been set to limit PM levels from vehicles, including compression ignition engine vehicles. The effect of increasing biodiesel content in the fuels has been investigated with respect to the PM using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). PM from tire emissions were compared against diesel PM using SEM, energy dispersive x-ray spectroscopy (EDS), TEM, particle size analysis, x-ray diffraction (XRD), and Raman spectroscopy (RS). The SEM and TEM show that increasing the biodiesel content decreased the size of the PM agglomerate particles, primary particles, and fringes. The EDS, RS, and XRD show that Tire PM are mostly carbon with silicon, calcium, zinc, and other various trace elements. They also allow comparisons with diesel PM for the carbon nanostructure. The particle size analysis shows that Tire PM are generally larger than engine derived PM. The TEM showed that the nanostructure of the carbonaceous Tire PM was the same fringe structure as the engine derived PM. The Tire PM was successfully characterized using similar methods as engine derived soot. There is strong relationship between the increasing of biodiesel content and reduction of agglomerate size, primary particle size and average fringe length.
      1