Karin, Preechar

Preferred name

Karin, Preechar

Alternative Name

Karin, P.

Karin, Preecha

Main Affiliation

School of Engineering

preechar.ka@kmitl.ac.th

Now showing 1 - 10 of 63

Some of the metrics are blocked by your
consent settings
Effects of variable O2 concentrations and injection pressures on the combustion and emissions characteristics of the petro-diesel and hydrotreated vegetable oil-based fuels under the simulated diesel engine condition
(2018-12-01)
Vo, C.
;
Charoenphonphanich, C.
;
Karin, P.
;
Susumu, S.
;
Hidenori, K.
This experimental research investigates the effects of variable O<inf>2</inf> concentrations and injection pressures on the combustion and emissions characteristics of the diesel (B7) and the hydrotreated vegetable oil (HVO)-based fuels. The O<inf>2</inf> concentrations included 21%, 15% and 10% O<inf>2</inf>, while the injection pressures were 80 and 120 MPa. The experimental fuels were the diesel fuel (B7), the neat HVO, the 20%, 50% and 80% HVO (by mass fraction) blended with the diesel. The experiments were carried out in a rapid compression-expansion machine (RCEM) under the direct injection (DI) diesel combustion condition. The analysis was undertaken using the two-color method. The experimental results indicated that the ignition delay, the heat release rate, the flame temperature, the soot density-KL factor, the NO<inf>x</inf> and soot-out emissions were inversely correlated to the HVO fraction in the blend. In addition, the findings revealed the similar flame profiles in which the higher flame temperature region and the darker KL density were concentrated around the spray flame upstream, regardless of the HVO mixing ratio. Besides, the decrease in the O<inf>2</inf> concentration resulted in the lower heat release rate, integral heat release, flame temperature, KL factor and NO<inf>x</inf> emissions but the longer ignition delay and higher soot concentration, with the highest soot concentration observed under the 15% O<inf>2</inf> environment. Nevertheless, the higher pressure differential (i.e. between the injection pressure and the ambient pressure) contributed to the shorter ignition delay, higher heat release rate, early peak of the flame temperature, wider combustion area, faster soot oxidation rate and higher NO<inf>x</inf> production.
Some of the metrics are blocked by your
consent settings
Physicochemical characteristics of ashes deposited on a wall flow diesel particulate filter of compression ignition engine
(2023-06-01)
Rodvanna, Sattatad
;
Srilomsak, Mek
;
Nuthong, Chaiwat
;
Charoenphanich, Chinda
;
Masomtob, Manop
The investigation of physicochemical characteristics of metal oxide ashes, deposited on a diesel particulate filter, was conducted using electron microscopy, energy dispersive spectroscopy, X-Ray fluorescence, and X-Ray diffractometry techniques. Iron is the main component of deposited ash on the DPF, and other ash components consisted of elements such as silicon, calcium, copper, sulfur, phosphorus, zinc, aluminum and minor chromium. It was clarified that this metal oxide ash has catalytic effect that contributed to an enhancement of soot oxidation. The apparent activation energies of soot oxidation on SiC powder and metal oxide ashes powder are approximately 169 and 135 kJ/mol, respectively.
Some of the metrics are blocked by your
consent settings
Injection Characteristics of Palm Methyl Ester Blended with Diesel Using Zuech’s Chamber
(2018-06-01)
Srichai, Prathan
;
Ewphun, Pop Paul
;
Charoenphonphanich, Chinda
;
Karin, Preechar
;
Tongroon, Manida
This research attempts to characterize the injection of palm biodiesel blended with diesel in a Zuech’s chamber. Thailand conventional diesel (mandated blend of biodiesel at 5 % or B5), palm biodiesel (B100) and four other biodiesel blends ratios (B20, B40, B60 and B80) were investigated with single hole injector of 140 and 200 μm diameters, injection pressure of 40 MPa to 160 MPa, constant back pressure of 4.5 MPa and energize time of 2.5 ms. The results show that increasing biodiesel blending ratios leads to longer injection delay, larger injection pressure drop, smaller injection quantity discharge coefficient (C<inf>d</inf>) and shorter injection duration. With increasing biodiesel blending ratio, high Cavitation number from biodiesel viscosity decreases Reynolds number. Increasing injector diameter from 140 μm to 200 μm has reduced injection delay, increased fuel injection quantity, discharge coefficient and remaining injection duration. The increasing of injection pressure were improve, injection delay, injection duration, injection quantity and discharge coefficient until injection pressure 120 MPa. In addition at injection pressure over 120 MPa are decrease injection quantity and discharge coefficient, it effect form the cavitation phenomena. Increasing of viscosity, density, Bulk modulus and sound velocity were effect to increase injection delay, with reduce injection quantity, injection duration and pressure drop during injection process.
Some of the metrics are blocked by your
consent settings
Comparison study on fuel properties of biodiesel from jatropha, palm and petroleum based diesel fuel
(2014-01-01)
Borhanipour, Morteza
;
Karin, Preechar
;
Tongroon, Manida
;
Chollacoop, Nuwong
;
Hanamura, Katsunori
The increase of air pollution and global warming is a threat for human life. Besides, the price of petroleum is increasing rapidly and the resources are diminishing. This obliged scientists and engineers to look for alternative sources of energy, which are cleaner and more sustainable. Biodiesel, defined as mono-alkyls of esters from vegetable oils and animals fat, is a cleaner renewable fuel and has been considered as the best alternative for petroleum based diesel fuel hence it can be used in any compression ignition engines without any significant modification. The main advantages of using biodiesel are its renewability and better quality of exhaust gas emissions due to their higher content of oxygen. The produce less soot and hence the feed stuck is plant it will regenerate the CO2 by the photosynthesis which ensures the renewability and reduces global warming. But these alternative fuels have faced some obstacles while utilizing in CI engines which are due to some of their physical and chemical characteristics. At this study the fuel properties of jatropha biodiesel and its blends (a non-edible feedstock) were compared with the properties of Palm biodiesel (an edible feedstock) and petroleum based diesel. The viscosity, density, oxidation stability, acid value, water content, iodine value, flash point, pour point, cloud point and calorific value of the samples were analyzed an discussed. The physical properties of the biodiesels are controlled by their chemical properties such as unsaturation level of fatty acids and oxidation stability. Results show that the viscosity of jatropha is higher than palm biodiesel although the density of palm biodiesel is higher. Oxidation stability of the biodiesel has impact on several chemical and physical properties and improvement of oxidation stability can make betterment in these properties. The results of this study will be used as a data backup for another research project. Copyright © 2014 SAE International and Copyright © 2014 TSAE.
Some of the metrics are blocked by your
consent settings
Characterization of carbon fiber and glass fiber's micro and nanostructure using electron microscopy, raman spectroscopy and xrd analysis
(2019-03-25)
Man, Tial Cuai
;
Karin, Preechar
;
Ohtake, Naoto
;
Aakasaka, Hiroki
;
Larpsuriyakul, Patcharee
Nowadays, most manufacturers are looking for the improvement of lightweight parts and other components in the automobile field. Carbon fiber and glass fiber are the most effective materials for their requirement to reduce the weight in vehicles due to their light weight and high tensile strength. The diameter of carbon fiber is 6 μm while glass fiber diameter is 17 μm. The mechanical tensile force of carbon fiber and glass fiber are 430 N and 290 N respectively on fiber alone without matrix. Carbon fibers are gradually smaller in each filament due to tensile force. Approximately 5 mm are elongated for both carbon fiber and glass fiber in tensile test report. In current research, characteristic and tensile force of carbon fiber and glass fiber were investigated by using electron microscopy, Raman spectroscopy and XRD.
Some of the metrics are blocked by your
consent settings
Effect of biofuel and soot on metal wear characteristic using electron microscopy and 3D image processing
(2017-11-05)
Karin, Preechar
;
Amornprapa, Warawut
;
Khamsrisuk, Phiranat
;
Budsayahem, Pol ake
;
Chammana, Pattara
The soot contamination in used engine oils of diesel engine vehicles was about 1% by weight. The soot and metal wear particle sizes might be in the range of 0-1 µm and 1-25 µm, respectively. The characteristics of soot affecting on metal wear was investigated. Soot particle contamination in diesel engine oil was simulated using carbon black. Micro-nanostructure of soot particles were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and laser diffraction spectroscopy (LDS). The metal wear behavior was studied by means of a Four-Ball tribology test with wear measured. Wear roughness in micro-scale was investigated by high resolution optical microscopy (OM), 3D rendering optical technique and SEM image processing method. It was found that the ball wear scar diameter increased proportionally to the soot primary particle size. The effect of biodiesel contamination were also increasing in wear scar diameter.
Some of the metrics are blocked by your
consent settings
EFFECT OF BIODIESEL ON COMPRESSION IGNITION ENGINE’S COMBUSTION BEHAVIOR AND PARTICLE EMISSION
(2020-11-11)
Tripatara, A.
;
Karin, P.
;
Phairote, W.
;
Charoenphonphanich, C.
;
Masomtob, M.
Diesel Engines are widely known for a high compression ratio, which is proportional to the engine’s efficiency. The effect from direct injection of a diesel engine generates particulate matter (PM). PMs are mainly composed of Soot and Metallic Ash, which are harmful to human health. This research describes thermal efficiency, engine performance and combustion behavior at various load (20%, 50%, and 80%) and fuel (B7, B20, and B100) by using combustion pressure analyzer. The experimental results demonstrated that B100 has the highest ISFC and lowest ISEC for all test series owing to the highest indicated thermal efficiencies. Operating load and fuel are strongly proportional to heat release rate and ignition delay. The heat release rate of low load condition is retarded compare with medium and high load. Conventional diesel and biodiesel PMs were investigated by using Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The average size of ultrafine particles that obtained from the experiment are range of 50-500 nm and primary nanoparticle size of B7 and B100 are in range of 25-50 nm.
Some of the metrics are blocked by your
consent settings
CHARACTERIZATION OF PARTICULATE MATTERS EMITTED FROM BIOMASS COMBUSTION USING ELECTRON MICROSCOPY AND ENERGY DISPERSIVE X-RAY SPECTROSCOPY
(2020-01-01)
Mon Oo, H.
;
Karin, P.
;
Masomtob, M.
;
Saisirirat, P.
;
Chollacoop, N.
Particulate Matters (PMs) emitted from biomass combustion including open burning of biomass agricultural residues, and forest fires must be reduced to protect both human health and the environment. The physical characteristics of morphology, elemental composition and nanostructure of particulate matters generated from biomass combustion were successfully investigated by using electron microscopy and energy dispersive X-ray spectroscopy (EDS) analysis with Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM), and thermogravimetric analysis (TGA) was used to analyze the oxidation kinetics of particulate matters. Before biomass burning, it was found that about 65% of carbon fraction in biomass raw material while 95% of carbon fraction in soot and 84% in ash particles after burning. The average diameter size of single primary particles is approximately 36 nm. Nanostructure of the single primary particle of biomass soot is mainly composed of curve line carbon crystallites while metallic ash nanoparticle is composed of straight-line hatch patterns. The inter-planar spacing of fringes of biomass soot and ash crystallites is 0.36 nm and 0.28 nm, respectively. This article aims to study the different nanostructure of biomass forest leaves residual ash and soot such as agglomerated particles, primary particle's measurement using TEM image analysis.
Some of the metrics are blocked by your
consent settings
Physicochemical characterization of forest and sugarcane leaf combustion's particulate matters using electron microscopy, EDS, XRD and TGA
(2021-01-01)
Oo, Hay Mon
;
Karin, Preechar
;
Chollacoop, Nuwong
;
Hanamura, Katsunori
Physical characteristics and quantitative elemental composition of PM and residual ash produced from sugarcane leaves (SCL) combustion were investigated using TEM-EDS compared with forest leaves (FRL). SEM-EDS was used to analyze the microstructure and chemical composition of biomass raw leaves and PM. XRD analysis was also performed to investigate the characterization of the crystalline nanostructure, structure of PM, and residual ash compared to the TEM image processing method. The oxidation kinetics of biomass raw materials, PM, and residual ash were investigated by TGA. The morphology of fine and ultrafine agglomerate structure of SCL soot and residual ash are not significantly different from the FRL soot and residual ash. The average diameter sizes of single primary nanoparticles of SCL and FRL soot are approximately 37 nm and 35 nm, while the sizes of residual ash are about 18 nm and 22 nm, respectively. The single primary nanoparticles of soot are mainly composed of curve line crystallites of carbon fringes, while residual ash is composed of straight-line lattice fringes. The average fringe lengths of SCL and FRL soot are about 1.25 nm and 1.04 nm from the outer shell and 0.89 nm and 0.74 nm from the inner core. The interlayer spacing of curve line carbon fringes of SCL and FRL soot is approximately 0.359 nm and 0.362 nm by the TEM image analysis and it was matched with XRD analysis. The biomass PMs are mainly composed of soot, Si, Ca, and K compounds: SiO<inf>2</inf>, CaCO<inf>3</inf>, and KCl.
Some of the metrics are blocked by your
consent settings
Oxidation Kinetics of Soot on Acicular Mullite Membrane Filter Using Electron Microscopy and Thermogravimetric Analysis
(2020-12-01)
Saenkhumvong, Eakkawut
;
Karin, Preechar
;
Charoenphonphanich, Chinda
;
Vittayakorn, Naratip
;
Hanamura, Katsunori
This paper investigates the oxidation kinetics of carbon black on acicular mullite using thermogravimetric (TGA) and mullite microstructures by scanning electron microscopy (SEM) for the development of diesel particulate filters (DPFs). It is observed that the amount of each chemical composition strongly affects the structure of mullite. The addition of AlF<inf>3</inf> and V<inf>2</inf>O<inf>5</inf> to mullite promotes the growth of needle-shaped mullite crystals. Thermogravimetric analysis was used to investigate and characterize chemical kinetics of soot oxidation for better understanding of designs and configurations of diesel particulate filters. The mass conversion of soot on the acicular mullite (ACM) is oxidized faster than that on the mullite (ML) membrane at all temperatures examined. The calculation of apparent activation energy (E<inf>a</inf>) of soot oxidation with isothermal methods on mullite was presented. The results showed that activation energy of soot oxidation is enhanced with ACM than with ML at all temperatures examined. The average calculated apparent activation energy of soot oxidation on ACM and ML are 146.4 kJ/mole and 155.3 kJ/mole, respectively.

Karin, Preechar

Filters

Settings

Sort By

Results per page