Charoenphonphanich, Chinda

Preferred name

Alternative Name

Charoenphonphanich, C.

Main Affiliation

School of Engineering

chinda.ch@kmitl.ac.th

Now showing 1 - 10 of 13

Some of the metrics are blocked by your
consent settings
Injection Characteristics of Palm Methyl Ester Blended with Diesel Using Zuech’s Chamber
(2018-06-01)
Srichai, Prathan
;
Ewphun, Pop Paul
;
Charoenphonphanich, Chinda
;
Karin, Preechar
;
Tongroon, Manida
This research attempts to characterize the injection of palm biodiesel blended with diesel in a Zuech’s chamber. Thailand conventional diesel (mandated blend of biodiesel at 5 % or B5), palm biodiesel (B100) and four other biodiesel blends ratios (B20, B40, B60 and B80) were investigated with single hole injector of 140 and 200 μm diameters, injection pressure of 40 MPa to 160 MPa, constant back pressure of 4.5 MPa and energize time of 2.5 ms. The results show that increasing biodiesel blending ratios leads to longer injection delay, larger injection pressure drop, smaller injection quantity discharge coefficient (C<inf>d</inf>) and shorter injection duration. With increasing biodiesel blending ratio, high Cavitation number from biodiesel viscosity decreases Reynolds number. Increasing injector diameter from 140 μm to 200 μm has reduced injection delay, increased fuel injection quantity, discharge coefficient and remaining injection duration. The increasing of injection pressure were improve, injection delay, injection duration, injection quantity and discharge coefficient until injection pressure 120 MPa. In addition at injection pressure over 120 MPa are decrease injection quantity and discharge coefficient, it effect form the cavitation phenomena. Increasing of viscosity, density, Bulk modulus and sound velocity were effect to increase injection delay, with reduce injection quantity, injection duration and pressure drop during injection process.
Some of the metrics are blocked by your
consent settings
Impact of Engine Oil Additives on Nanostructure and Oxidation Kinetics of Diesel and Synthetic Biodiesel Particulate Matters using Electron Microscopy
(2019-12-19)
Koko, Phyozin
;
Karin, Preechar
;
Charoenphonphanich, Chinda
;
Chollacoop, Nuwong
;
Hanamura, Katsunori
Physicochemical characteristics of particulate matters which are influenced by engine oil additives from engine combustion of diesel and synthetic biodiesel: Hydrotreated vegetable oil (HVO) were successfully investigated using electron microscopy, electron dispersive X-ray spectroscopy and thermogravimetric analysis. The agglomerate structure of diesel PM, HVO PM and diesel blending lubricant PM are similar in micro-scales. However, nanostructure of soot is a spherical shape composed of curve line crystallites while the metal oxide ash nanostructure is composed of parallel straight line hatch patterns. The oxidation kinetics of fuel blending lubricant PMs are higher than neat fuel PMs due to catalytic effect of incombustible metal additives from engine lubricating oil.
Some of the metrics are blocked by your
consent settings
Physical characterization of biodiesel particle emission by electron microscopy
(2013-01-01)
Karin, Preechar
;
Songsaengchan, Yutthana
;
Laosuwan, Songtam
;
Charoenphonphanich, Chinda
;
Chollacoop, Nuwong
Nanostructures of diesel and biodiesel engine particulate matters (PMs) were investigated by using a Transmission Electron Microscopy (TEM). The average single particle sizes of biodiesel and diesel PMs are approximately 30-40 nm and 50-60 nm, respectively. Image processing process was used to estimate each carbon platelet length by using TEM image. The average carbon platelet length of biodiesel and diesel PMs are in the range of 0.1-7.0 nm. Moreover, carbon atoms per cubic volume of PMs are approximately 500-900. The result shows that engine load and fuel property are strongly impact on the size of single particle and carbon atom density of particle. This is one of interesting behaviors need to be investigated for better understanding. The results of this research would be used as basic information for design and develop removing process of PM emitted from engine combustion which using in diesel and biodiesel fuels. © Copyright @2013 SAE Japan and Copyright @ 2013 SAE International.
Some of the metrics are blocked by your
consent settings
Physicochemical Characterization of Diesel Engine’s Soot and Metal Oxide Ash Nanoparticles Using Electron Microscopy, EDS and TGA
(2021-06-01)
Karin, Preechar
;
Koko, Phyozin
;
Charoenphonphanich, Chinda
;
Chollacoop, Nuwong
;
Hanamura, Katsunori
Physicochemical characteristics of metal oxide ash derived from engine oil additives on particulate matter (PM) from a diesel direct injection compression ignition (DDI-CI) engine, in terms of nanostructure and oxidation kinetics, were investigated through electron microscopy, energy dispersive X-ray spectroscopy and isothermal thermogravimetric analysis. Diesel and synthetic biodiesel were used as the baseline fuel. Engine performance and combustion characteristics of neat diesel and synthetic biodiesel fuel were initially reported. To enhance the formation of ash derived from lubricant additives, an accelerated ash loading method was used by dosing 10% by mass directly into the fuels. Different single primary particle nanostructures of soot and metal oxide ash were clearly observed. Single primary particle nanostructure of soot was a spherical shape composed of curve line carbon crystallites, while nanostructure of metal oxide ash was a spherically round outline shape comprised with parallel straight-line lattice fringes. Soot oxidation kinetics was significantly enhanced due to the presence of metal oxide ashes in the engine’s PM. In addition, the elemental analysis of metal oxide ash, derived from engine oil additives, was investigated using electron dispersive X-ray spectroscopy.
Some of the metrics are blocked by your
consent settings
Physicochemical characterization of direct injection Engines's soot using TEM, EDS, X-ray diffraction and TGA
(2021-06-01)
Oo, Hay Mon
;
Karin, Preechar
;
Charoenphonphanich, Chinda
;
Chollacoop, Nuwong
;
Hanamura, Katsunori
The physical characteristics and elemental composition of particulate matters (PMs) from gasoline direct injection spark ignition (GDI-SI) engines were successfully investigated using transmission electron microscopy - energy dispersive X-ray spectroscopy (TEM-EDS). Thermogravimetric analysis (TGA) was used to analyze the PMs oxidation. The morphology of agglomerated GDI-PMs is not significantly different from the diesel direct injection compression ignition (DDI-CI) engine's PMs. The spherical single primary nanoparticles of the engine's soot composed of curve line carbon crystallites. The average diameter size of the single primary nanoparticles of GDI, DDI, and carbon black are approximately 24 nm, 26 nm, and 31 nm, while the inter-planar spacing is about 0.364 nm, 0.358 nm, and 0.356 nm, respectively. The total fringe lengths of GDI, DDI, and carbon black are approximately 154 nm, 159 nm, and 163 nm measured from the areas of 10 nm × 10 nm inner core regions of primary nanoparticles, and are 180 nm, 195 nm, and 228 nm from the outer shell regions, respectively. The total fringe lengths of inner core are shorter than the outer shell. Besides, the engine's PMs contains both crystalline and amorphous carbon structure using XRD analysis. The GDI-PMs had the least crystalline structure compared to the DDI-PMs and carbon black due to the higher percentage of amorphous fraction. TGA analysis showed that the GDI-PMs oxidation was faster than the DDI-PMs and CB-N330 oxidation because of the primary particle size, the fringe length, and the crystal size which have an impact on oxidation kinetics of particulate matters.
Some of the metrics are blocked by your
consent settings
Characterization of Biodiesel Particle Emission in Trapping and Regeneration Processes on Cordierite Diesel Particulate Filter
(2015-11-17)
Siricholathum, Komkla
;
Karin, Preechar
;
Charoenphonphanich, Chinda
;
Hanamura, Katsunori
;
Chollacoop, Nuwong
As well-known, the diesel engine has the highest thermal efficiency at the same load as compared with internal combustion engine but its disadvantage is particulate matter (PM) emitted to the atmosphere. The studies of this paper were divided into two parts. The first part studied the quantity of PM from the both diesel and biodiesel fuels at 80% load (2400 rpm) by the trapping process on diesel particulate filter (DPF) used in a partial flow dilution tunnel. The second part studied the regeneration process of PM under the flow rate of oxygen and nitrogen gas of 13.5 L/min with 10%, 15%, and 21% of oxygen gas. The result showed that amount of PM from biodiesel fuel was lower around two times than PM from diesel fuel. The duration in regeneration process of biodiesel's PM was shorter than diesel while increasing of oxygen percentage can reduce regeneration time.
Some of the metrics are blocked by your
consent settings
Influence of ethanol-biodiesel blends on diesel engines combustion behavior and particulate matter physicochemical characteristics
(2022-12-01)
Karin, Preechar
;
Tripatara, Aphichai
;
Wai, Phyo
;
Oh, Ban Seok
;
Charoenphonphanich, Chinda
Ethanol-blended biodiesel fuel can reduce smoke emissions by over 50% on both a single-cylinder engine and a four-cylinder engine. The average single primary particle size of biodiesel blended diesel, biodiesel, and ethanol blended biodiesel soot are approximately 30, 27, and 29 nm, respectively. The maximum graphene fringe length of biodiesel blended diesel, biodiesel, and ethanol blended biodiesel CI engine's soot are approximately 5.2, 4.6, and 4.5 nm. The carbon atom density of soot particles emitted from the diesel, biodiesel, and ethanol blended biodiesel CI engines are approximately 102, 91, and 88 atoms/nm3.
Some of the metrics are blocked by your
consent settings
Experimental investigation of the influence of ethanol and biodiesel on common rail direct injection diesel Engine's combustion and emission characteristics
(2022-11-01)
Wai, Phyo
;
Kanokkhanarat, Phobkrit
;
Oh, Ban Seok
;
Wongpattharaworakul, Veerayut
;
Depaiwa, Nattawoot
This study aims to characterize the effect of oxygenated biofuels in diesel engine combustion, thermal efficiency, and emission by blending different percentages of ethanol and biodiesel with fossil fuel derived diesel. In this research, 5% and 10% by weight of bioethanol were added to commercial B10 (10% biodiesel and 90% diesel), B20 (20% biodiesel and 80% diesel) and B100 (100% biodiesel) and experimented on using a 3 L four-cylinder common rail diesel engine. The experiment was performed under three engine speeds of 1000 rpm, 1500 rpm, and 2000 rpm with three constant engine torques of 56 Nm, 84 Nm, and 140 Nm. The results show that ethanol-biodiesel-diesel ternary blended fuels are higher in premixed combustion pressure and net heat release rate (NHRR) peaks. The cumulative heat release of ethanol blended fuels is also higher for ethanol blended fuels. The fuel consumption increased with the ethanol and biodiesel percentage in the blended fuels due to the lower heating value while the brake thermal efficiency did not decrease. It was clearly observed that the particle emission could be reduced by more than 50% when ethanol and biodiesel percentage increased.
Some of the metrics are blocked by your
consent settings
Experimental investigation in combustion characteristics of ethanol-gasoline blends for stratified charge engine
(2011-01-01)
Charoenphonphanich, Chinda
;
Ornman, Piyaboot
;
Karin, Preechar
;
Kosaka, Hidenori
;
Chollacoop, Nuwong
The increasing of global energy demand and stringent pollution regulations have promoted research on alternative fuels. In Thailand, ethanol, can be produced from many sources of national agriculture products as renewable fuel, which was strongly promoted by government due to its many merits for use in transportation field. In this study, combustion characteristics of ethanol-gasoline blend (20%, 85%, and 100%) as well as pure gasoline (E0) were investigated by using a swirl-generated constant volume combustion chamber. Flame propagations of different fuel blends were observed by high speed Schlieren photography technique while pressure history data were recorded for detailed combustion analysis. Combustion behavior, combustion duration and rate of pressure rise of all tested fuels were investigated in various swirl intensities and equivalence ratios. In addition, effect of swirl intensities and ethanol concentration on lean misfire limit were also discussed. The results showed that the high concentration of ethanol blend with the high swirl intensity can significantly extended lean misfire limit while lowering combustion variations. Furthermore, combustion duration can be accelerated by increasing the percentage of ethanol in fuel blend. Through this study, a better understanding of stratified charge combustion fuelled with ethanol/gasoline blends can be achieved. Copyright © SAE Japan and Copyright © 2011 SAE International.
Some of the metrics are blocked by your
consent settings
Impact of biodiesel on small CI engine combustion behavior and particle emission characteristic
(2017-01-01)
Karin, Preechar
;
Watanawongskorn, Park
;
Boonsakda, Jiramed
;
Saenkhumvong, Eakkawut
;
Rungsritanapaisan, Sippakorn
Diesel engines are high thermal efficiency because of high compression ratio but produce high concentration of particulate matter (PM) because of direct injection fuel diffusion combustion. PM must be removed from the exhaust gas to protect human health. This research describes biodiesel engine performance, efficiency and combustion behavior using combustion pressure analyzer. It was clearly observed that PM emitted from CI engines can be reduced by using renewable bio-oxygenated fuels. The morphology and nanostructure of fossil fuel and biofuel PMs were investigated by using a Scanning electron microscopy (SEM) and Transmission electron microscopy (TEM). The morphology of biodiesel and diesel doesn't have much different in the viewpoint of particulate matter trapping using DPF micro surface pores. The agglomerated ultrafine particles and primary nanoparticles sizes of diesel and biodiesel engine's PM are approximately 50-500 nm and 20-50 nm, respectively. The primary particle of biodiesel engine's PM is smaller than that of fossil diesel. The average of diesel and biodiesel PM's carbon platelets is in the range of 0.2-5.2 nm.

Charoenphonphanich, Chinda

Filters

Settings

Sort By

Results per page