KMITL

Permanent URI for this communityhttps://dspace.kmitl.ac.th/handle/123456789/1

Browse

Search Results

Now showing 1 - 10 of 29

Some of the metrics are blocked by your
consent settings
Impact of particulate filters on biodiesel and diesel fuel: a comparative study of thermal efficiency and emissions
(2026-06-01)
Suteerapongpun, Teerapat
;
Patkacha, Atikan
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Saisirirat, Peerawat
This study investigated the influence of a partial-flow (P-DPF) and a full-flow (F-DPF) diesel particulate filter on the combustion and emissions of a light-duty diesel engine fueled with conventional diesel (B7) and pure biodiesel (B100). The engine was operated on a dynamometer under engine speeds of 1600–2000 rpm at 84–140 Nm loads. The results revealed that while B100 had higher mass-based specific fuel consumption (BSFC) due to its lower energy density, its overall brake thermal efficiency (BTE) was comparable to that of B7, indicating similar energy conversion efficiency. The use of DPFs resulted in a modest efficiency penalty, with brake thermal efficiency decreasing by 0.07% for the P-DPF and 2.62% for the F-DPF. The emissions analysis revealed the trade-offs associated with biodiesel use and DPF integration. While baseline B100 operation produced substantially higher nitric oxide (NO) emissions relative to B7, it consistently generated much lower smoke opacity. When averaged across all three aftertreatment configurations (no DPF, P-DPF, and F-DPF), B100 reduced smoke emissions by approximately 59% compared with B7. Additionally, the P-DPF and F-DPF proved effective at reducing smoke to half and near-zero levels, respectively, for both fuels.
Some of the metrics are blocked by your
consent settings
In-cylinder combustion and emission characteristics of a 3L compression ignition engine using pure biodiesel fuel blended with 5% ethanol
(2026-04-01)
Suteerapongpun, Teerapat
;
Huynh, Trung An
;
Aung, Sonekhar Jarring
;
Thin, Myat Hsu
;
Thaeviriyakul, Poonnut
This study investigates the combustion performance, efficiency, and emission characteristics of four fuel blends—B7 (7% biodiesel), B100 (pure biodiesel), B100E5 (95% biodiesel + 5% ethanol), and B100E10 (90% biodiesel + 10% ethanol)—in a light-duty diesel engine. Experiments were conducted on an engine dynamometer under varying loads (84, 112, and 140 Nm) and speeds (1600, 1800, and 2000 rpm) to assess in-cylinder pressure, temperature, engine efficiencies, and emissions. The results demonstrate that the oxygenated B100Es blend achieves superior combustion performance, exhibiting higher peak in-cylinder pressures and temperatures than conventional B7, attributable to enhanced oxygen availability, which promotes more complete fuel oxidation. This translates to an improvement in indicated thermal efficiency despite its lower calorific value relative to B7. B100 demonstrates distinct advantages in mechanical efficiency at higher engine speeds, attributed to its superior lubricity. The study provides quantitative evidence that a strategic blend of biodiesel with ethanol can effectively balance the often-competing objectives of combustion efficiency and emission reduction in modern diesel engines. The average brake thermal efficiencies of B7, B100, B100E5, and B100E10 are approximately 35.8, 36.4, 37.7, and 37.2%, respectively. Additionally, the average smoke intensities of B7, B100, B100E5, and B100E10 are approximately 0.211, 0.075, 0.042, and 0.038%/kW, respectively.
Some of the metrics are blocked by your
consent settings
Influence of ethanol-blended B7-diesel on in-cylinder combustion characteristic, engine thermal efficiency and emission of a 3L-compression ignition engine
(2026-03-01)
Suteerapongpun, Teerapat
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Saisirirat, Peerawat
;
Po-ngaen, Watcharin
This study investigated the effects of blending weight ratio of 5% and 10% ethanol (B7E5 and B7E10) with standard B7-diesel on the performance, combustion, and emission characteristics of a light-duty common-rail diesel engine. The engine was tested on a dynamometer across various speeds (1600–2000 rpm) and loads (84 and 112 Nm) to analyze in-cylinder pressure, thermal efficiencies, and exhaust emissions. Results indicated significant emission benefits, especially at high loads. The B7E10 blend reduced smoke intensity by approximately 75% and carbon dioxide emissions by 34% compared to the baseline B7. The performance analysis revealed a critical trade-off associated with the ethanol blends: while the inherent oxygen content in ethanol significantly improved the indicated thermal efficiency (ITE) through enhanced combustion, its lower viscosity simultaneously led to increased frictional losses. Consequently, these competing effects resulted in only a modest improvement in brake thermal efficiency (BTE) and comparable brake-specific energy consumption (BSEC) compared to the baseline B7. The primary objective is to identify the benefits and trade-offs associated with ethanol blending in biodiesel-based diesel fuels that are compatible with existing diesel vehicles.
Some of the metrics are blocked by your
consent settings
Development of a Hybrid Electric Motorcycle Powertrain with Energy Management Strategy Implementation
(2026-01-01)
Song, Toan Pham Vo
;
Karin, Preechar
;
Masomtob, Nanthikan
;
Ngo, Duy Nhat
;
Kosaka, Hidenori
This paper presents a Hybrid Electric Vehicle (HEV) motorcycle that combines a 7.5 kW Internal Combustion Engine (ICE) with a 3 kW brushless DC motor wheel (DCMW). The HEV motorcycle is modelled using the MATLAB/Simulink simulation environment, based on experimental data obtained from dyno chassis testing of ICE and DCMW motorcycles. In the simulation, various HEV system algorithms are tested and optimized to improve fuel consumption, using the World Motorcycle Test Cycle (WMTC) as a benchmark, in comparison with the same conventional ICE motorcycle. The results show that the HEV configuration achieves a fuel consumption of 79.29 km/liter, compared to 52.63 km/liter for the ICE-only configuration. In conclusion, the HEV system's algorithm effectively improves fuel efficiency and represents a fundamental step toward the reliable control of the inverter and electronic injector using a microcontroller in future development.
Some of the metrics are blocked by your
consent settings
Particle emission and thermal efficiency analysis of a diesel vehicle using biodiesel and a platinum metallic partial-flow particulate filter
(2025-01-01)
Dang, Huy Quang
;
Phyo, Mi Zwe Mon
;
Thaeviriyakul, Poonnut
;
Cosh, Plan Teekatasn
;
Srilomsak, Mek
Harmful emissions from diesel vehicles, particularly unmodified ones, pose significant concerns for human health and the environment, underscoring the urgency to address these issues. This study investigated the effects of commercial fuels, B10, B20, and biodiesel B100, used with a metallic partial-flow catalyzed diesel particulate filter (P-CDPF), on a light-duty unmodified diesel vehicle's thermal efficiency and emissions characteristics. The initial test was conducted on a chassis dynamometer to measure the fuel flow rates at three different engine speeds, 1500, 2000, and 2500 rpm, with four loads, 84, 112, 140, and 160 Nm. This was done to evaluate brake-specific fuel consumption and brake thermal efficiency under steady-state conditions. The second test followed the new European driving cycle to examine emission factors of regulated pollutants under both urban and highway driving conditions. The results indicated that BSFC values increased with the biodiesel ratio in the blends, attributed to lower heating values. However, higher oxygen contents with increasing biodiesel ratios led to more complete combustion and improved brake thermal efficiency. Installation of a P-CDPF had a minimal impact, resulting in less than a 3.4% increase in the BSFC and a 1% decrease in brake thermal efficiency across all tested fuels, owing to its relatively low pressure drop. Increasing the biodiesel ratio from B10 and B20 to B100 resulted in reductions of up to 32% of particulate mass and 45% of particulate number in vehicle emissions. P-CDPF installation further reduced particulate mass by over 60% and particulate number by 36% across all tested fuels, demonstrating its effectiveness in trapping and passively oxidizing particulate matter. Furthermore, the P-CDPF significantly reduced harmful gases with addition of a catalytic coating. A combination of a P-CDPF and commercial biodiesel fuels emerges as an effective solution for reducing regulated emissions from unmodified diesel vehicles.
Some of the metrics are blocked by your
consent settings
Effect of a retrofitted metallic microfiber partial flow diesel particulate filter on a light duty diesel vehicle particle emission characteristics
(2024-02-01)
Mon Phyo, Mi Zwe
;
Phairote, Watanyoo
;
Srilomsak, Mek
;
Charoenphonphanich, Chinda
;
Masomtob, Manop
This study was conducted two distinct experiments, using a light-duty diesel vehicle at various engine speeds and loads as well as the new European driving cycle (NEDC) comparing commercial diesel fuel (B7) and pure biodiesel (B100). The NEDC involves a combination of urban and extra urban driving conditions. It aims to study a diesel vehicle's thermal efficiency as well as its gaseous and particulate matter (PM) emissions. This involves comparing results with and with no diesel oxidative catalyst (DOC) and a partial flow diesel particulate filter (PDPF) system. The surface morphology, micro- and nanostructure of a diesel vehicle's PM were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and thermogravimetric analysis (TGA) to determine nanostructural and dimensional changes after mounting a DOC-PDPF system. Comparison of B7 and B100 combustion showed that B100 had around 1 % increase in brake thermal efficiency (BTE) at 1500 and 2000 rpm compared to B7 since B100 is a more oxygenated biofuel. At 2500 rpm, similar BTE values were observed. Introduction of a DOC-PDPF system resulted in an approximately 1 % BTE reduction for both fuels. This was due to greater friction losses caused by backpressure from the DOC-PDPF system. Increased exhaust backpressure was progressive, ranging from 1 kPa at idle speed to 6 kPa at high engine speeds for both tested fuels. The DOC-PDPF system respectively minimized PM emissions and particle numbers (PNs) by more than 50 % and 35 % for B7 and 71 % and 31 % for B100. These results are average values under the various phases of NEDC testing. A 30 % decrease in PM and a 44 % reduction in PNs under the overall test cycle were found when B100 was tested compared to B7. The soot primary particle size was reduced from 34.69 to 29.08 nm and the carbon fringe length diminished from 1.25 to 0.949 nm at different pre- and post-DOC-PDPF locations. This was due to partial oxidation on the surfaces of the PDPF metallic microstructure. PM undergoes simultaneous partial oxidation after passing through the DOC-PDPF system, as confirmed by TGA analysis.
Some of the metrics are blocked by your
consent settings
The impact of a metallic partial-flow particulate filter on diesel engine combustion and emission characteristics using palm oil biodiesel blends
(2024-02-01)
Thin, Myat Hsu
;
Liu, Hai
;
Thaeviriyakul, Poonnut
;
Wai, Phyo
;
Oh, Ban Seok
Reducing particulate emissions from diesel engines pose a significant challenge in developing countries due to increasingly stringent regulations for both new and older vehicles. While employing wall-flow filters have proven effective for new vehicles, older vehicles necessitate alternative approaches to particulate filtration without complex modifications. Partial flow filters exhibit advantages in such scenarios, characterized by their lack of external components, simplified design, minimal maintenance demands, and resilience to misfuelling. The present study mainly focuses on the evaluation of a partial flow diesel particulate filter (P-DPF) installed on a diesel direct injection compression ignition engine, operating on commercial biodiesel blends, specifically B10 and B20. According to the combustion analyses, the combustion pressure, temperature, and the heat release rate increased with the kinetic energy inside the residual gas molecules due to installation of the P-DPF system. This also resulted in higher indicated power as well as indicated thermal efficiency. However, brake-specific fuel consumption and brake-specific energy consumption, exhibited only a marginal increase, while brake thermal efficiency experienced a slight decrease of 0.65% in the case of B10 and 0.74% for B20 after the installation of the P-DPF system due to the friction loss by the filter backpressure. Furthermore, an incremental increase in exhaust backpressure was observed, ranging from 0.2 kPa at 1000 rpm and 56 Nm to 2.25 kPa at 2000 rpm and 140 Nm. An analysis of emissions limits showed a notable 65% reduction in soot emissions. Comparative analyses were conducted to assess the impact of P-DPF installation on a diesel engine without any manual changes. Ultimately, the partial flow filter (P-DPF) emerges as an effective initial measure in mitigating particulate matter emissions, particularly when employed in a retrofit exhaust after-treatment system.
Some of the metrics are blocked by your
consent settings
Experimental investigation of metallic partial-flow particulate filter on a diesel engine's combustion pressure and particle emission
(2023-09-01)
Mon Phyo, Mi Zwe
;
Wai, Phyo
;
Thin, Myat Hsu
;
Oh, Ban Seok
;
Phairote, Watanyoo
The study aims to present the combustion and exhaust behaviors of a 3 L, four-cylinder common rail diesel engine with three different kinds of conventional B7 diesel fuels with and without a platinum diesel oxidation catalyst (DOC) system and non-catalytic partial flow through a diesel particulate filter (P-DPF). Testing is performed under the three different operating conditions, idle to medium engine loading at 1000, 1500, and 2000 engine revolutions per minute with four different engine torques of 84, 112, 140 and 160 Nm. The surface morphology and agglomerate size of particulate matter (PM), single primary particle analysis as well as the fringe length of the carbon crystallite structure were also examined using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy dispersive x-ray spectroscopy (EDS) to achieve a better understanding through image processing. The P-DPF system does not have a significant effect on an engine's in-cylinder combustion characteristics and brake thermal efficiency. The diesel engine's particle emissions are reduced by trapping them on the metallic micro-fibers of a P-DPF. CO<inf>2</inf>, NO, and O<inf>2</inf> levels show that the carbonaceous particle emissions on the micro-structure of the P-DPF passively react with NO<inf>2</inf> and O<inf>2</inf>. Consequently, diesel engine particle emissions can be reduced by around 50% using a P-DPF system under the experimental conditions of the current study.
Some of the metrics are blocked by your
consent settings
Physicochemical characteristics of ashes deposited on a wall flow diesel particulate filter of compression ignition engine
(2023-06-01)
Rodvanna, Sattatad
;
Srilomsak, Mek
;
Nuthong, Chaiwat
;
Charoenphanich, Chinda
;
Masomtob, Manop
The investigation of physicochemical characteristics of metal oxide ashes, deposited on a diesel particulate filter, was conducted using electron microscopy, energy dispersive spectroscopy, X-Ray fluorescence, and X-Ray diffractometry techniques. Iron is the main component of deposited ash on the DPF, and other ash components consisted of elements such as silicon, calcium, copper, sulfur, phosphorus, zinc, aluminum and minor chromium. It was clarified that this metal oxide ash has catalytic effect that contributed to an enhancement of soot oxidation. The apparent activation energies of soot oxidation on SiC powder and metal oxide ashes powder are approximately 169 and 135 kJ/mol, respectively.
Some of the metrics are blocked by your
consent settings
Effect of Metallic Microfiber Flow Through Diesel Particulate Filter System on Diesel Engine’s Particle Emission Physicochemical Characteristics
(2023-03-01)
Oh, Ban seok
;
Thaeviriyakul, Poonnut
;
Phairote, Watanyoo
;
Srilomsak, Mek
;
Charoenphonphanich, Chinda
It is well known that particulate matter (PM) from diesel compression ignition engines is harmful to the environment and to human health. To reduce engine PM emissions, exhaust after-treatment systems are utilized. A basic high-performance system can be composed of a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF). This study used a system composed of a DOC and a partial flow DPF. Partial flow refers to how only a portion of the exhaust gas is filtered using metal fibrous filters instead of the full flow using ceramic filters. The PM deposited on the side wall of the stages of the system was investigated with respect to elemental composition, morphology, and nanostructure. This was to determine the effect of each component on the PM. The elemental composition analysis found traces of the engine lubricant oil in the PM collected before entering the DOC. This was then eliminated by the DOC and the remaining PM was not significantly impacted by the exhaust after-treatment system. The morphology and nanostructure show an interesting relationship where the size of the single primary particles increased while the graphitic nature of the carbon in the PM seemed to decrease. This can be explained by the simultaneous nature of partial trapping and partial oxidation that occurs in the partial-flow DPF. The emission measurements of opacity, temperature, CO<inf>2</inf>, NO, and O<inf>2</inf> from each position also support this.

KMITL

Browse

Filters

Settings

Sort By

Results per page

Search Results